Are you looking for Dodge Charger bolt pattern? or just want to know about the Dodge Charger bolt pattern? We’ll explain everything you need to know about the Dodge Charger Bolt Pattern.
There are two ways to find the bolt pattern of your Dodge Charger. You can either take the outside edge of one bolt and measure to the center of the opposite bolt.
Then you can multiply the diameter of that imaginary circle by the number of bolts. The result is the bolt pattern. Using these two measurements, you will find the bolt pattern of your car.
- 1 Dodge Charger Wheel Bolt Pattern
- 2 Dodge Charger Bolt Pattern and Rim Width
- 3 Dodge Charger Bolt Pattern and The Tire Size
Dodge Charger Wheel Bolt Pattern
When you want to install new wheels, you need to know the wheel bolt pattern for your Dodge Charger. Luckily, it is relatively simple to determine the correct size and bolt pattern for your rims. You can easily find out your bolt pattern by looking at the center of the bolt across from your stud. You can then add the number of bolts to get the diameter. The bolt pattern will determine the size of your tire.
Once you know the bolt pattern for your Charger, you can start shopping for new wheels. Measure the distance between the outer edge of one bolt and the center of the opposing bolt. This will give you the overall diameter of the bolt pattern for your Charger. Once you know the exact measurement, you can determine which type of wheels will fit your car.
The bolt pattern for all Dodge Chargers manufactured between 2005 and present is 5 x 4.53 inches (5x115mm). For Dodge Chargers manufactured between 1983 and 1987, the bolt pattern is 4 x 3.94 inches (4x100mm). Finally, for those Chargers manufactured between 1966 and 1978, the bolt pattern is 5×4.5 inches (5×114.3 mm).
The wheel bolt pattern for your Dodge Charger is S5 X 115 mm. Choosing the correct wheel is important, as improper ones can cause premature tire wear, feathering, and cupping problems. It is recommended that you use OEM wheels when buying new wheels. Using aftermarket wheels can affect your car’s fuel consumption and speedometer readings and can lead to fines in some states.
It is important to note that you should also check the offset of your Dodge Charger wheels. The offset is often printed on the mounting plate, the spoke back, or the back of the wheel. This offset is usually indicated by the letters ET.
Dodge Charger Bolt Pattern and Rim Width
The rim width of your Dodge Charger is an important factor when choosing your tires. It will determine the size of your tires, as a narrow rim will make your tires narrower. However, be careful when choosing the correct rims, as the rim width can change during fitment. Also, the quality of the rims you choose may affect the width of your tires, as high-quality tires can stretch as much as 5 mm.
When choosing the right rims for your Dodge Charger, you should also consider the bolt pattern of the wheels. This bolt pattern is S5 X 115mm. If the bolt pattern is wrong, you might end up with premature tire wear, cupping, or feathering.
To prevent these problems, you should check the bolt pattern monthly. If you find that the bolts have become loose, it is time to replace the tires. Ideally, you should replace your tires every 30,000 to 50,000 miles.
Another important factor to consider is the center bore. The center bore is the diameter of the hole where the hub and rim meet. If the center bores are different, you might not be able to get a proper fit. If this is the case, you should make sure you select a wheel with the same center bore size. Otherwise, your wheels might lose grip when you turn corners.
In addition to the lug diameter, rim width is another important factor to consider. If you don’t know the bolt diameter, you might consider using an adapter. Adapters allow you to change the lug pattern.
Center Bore Dodge Charger 2015 – 2018 – Present
The center bore for a Dodge Charger manufactured between 2015, 2018 and present-day is 71.6 mm with five lug nuts. The thread size for these bolts is M14 x 1.5 and needs to be tightened with 130 lb-ft (176 Nm).
Center Bore Dodge Charger 2011 – 2014
The center bore of Dodge Chargers manufactured between 2011 and 2014 is 71.6 mm, and they have five lug nuts with a thread size of M14 x 1.5. These bolts need to be tightened with 130 lb-ft (176 Nm).
Center Bore Dodge Charger 2005 – 2010
The center bore for Dodge Chargers manufactured between 2005-2010 is 71.6 mm and they have five lug nuts with a thread size of M14 x 1.5. RWDs and Daytonas need to have their bolts tightened with 110 lb-ft (149 Nm), while Police editions require 140 lb-ft (190 Nm).
Center Bore Dodge Charger 1983 – 1987
The Dodge Charger manufactured between 1983 and 1987 with a 2.2L engine has a center bore of 57.1 mm and four lug nuts that need to be tightened with 95 lb-ft (129 Nm). The standard tire size for this model is 175/75R13 and the rim size is 5Jx13 ET35.
Center Bore Dodge Charger 1966 – 1978
The center bore of Dodge Chargers manufactured between 1966 and 1978 is 71.6 mm, and they have five lug nuts with 1/2″ – 20 UNF thread size.
Dodge Charger Bolt Pattern and The Tire Size
When replacing your wheels and tires, you need to know the tire size that fits your Dodge Charger’s bolt pattern. This information can be found in your car’s owner’s manual. Also, you should look at the offset of your current wheels to find the right offset for your car.
When choosing the correct tire size for your Dodge Charger, you should consider the driving conditions and weather. Many drivers in four-season states purchase two sets of tires to maximize their performance and safety. Other drivers prefer all-season tires for convenience. No matter what type of driving you do, you will want to ensure that your Dodge Charger is properly protected.
Your Charger’s rim width can also affect the tire size. A wide rim will require a wider tire, while a narrow rim will require a narrower one. Moreover, the rim width may change during the fitment process. In addition, the width of your tire will vary depending on the quality of the tire. High-quality tires can stretch as much as 5mm.